Model Attributes

Local Attributes

Local attributes apply to individual nodes in the network model. This section lists the most important model attributes for the UE, Node-B, RNC, CN, and Repeater node models. For detailed information about a particular attribute, see its description by clicking on the Details button in the Attributes dialog box.

UE Attribute

Table 241: UE Attributes

Use This Attribute… To…
UE IMSI Specify the International Mobile Subscriber Identity of the UE. You should set this attribute if you need to specify a source and destination for traffic that is going to be generated between station UE nodes.
UE Serving SGSN ID Specify the CN Identifier of the CN (SGSN) node that the UE should attach to (applies only to workstation and server UE nodes). When auto-assigning IP addresses, the model uses this attribute value to ensure that the UE is in the same IP subnet as the CN node. If the network modeled contains only one CN, no configuration is necessary since the default value of all SGSN IDs and UE Serving SGSN IDs is 0.
UMTS GMM Timers Specify the following timers:
• T3310, which starts when the UE sends a GPRS attach request message.
• T3380, which starts when the UE sends an activate PDP context request message to the SGSN.
• T3317, which starts when the UE sends a service request message to the SGSN.
UMTS Logical Channel Configuration Specify channel mapping type, logical channel assignments, and MAC queuing scheme (priority and weight details).
UMTS PDCP Compression Configure the PDCP Header Compression feature on the UE node for uplink transmissions.
If activated, IP/UDP and TCP/IP headers will be compressed for all higher layer packets arriving to the UMTS layer. Header compression ratio is computed based on the configured probability distribution function and its argument(s). Notice that just UDP/IP compression will be used for UMTS station models.
A different compression ratio can be specified for IP/UDP and TCP/IP cases.
QoS Profile Configuration Configure each UMTS service class (conversational, streaming, interactive, and background). The majority of UMTS QoS profile configuration attributes are described below.
Allocation/Retention Priority
(sub-attribute of QoS Profile Configuration)
Configure parameters for the allocation and retention of a RAB during admission control. Use this attribute to enable queuing for the RAB request, and to specify if the RAB request can preempt or be preempted by other requests.
Bit Rate Config
(sub-attribute of QoS Profile Configuration)
Specify the expected maximum and guaranteed bit rates for the uplink and downlink communication. These values need to be specified carefully. A too low value may cause consistent saturation of the QoS buffer and hence the loss of communication. A too high value would cause resource wastage in the cells with which the UE has established radio links.
Delivery Order
(sub-attribute of QoS Profile Configuration)
Specify if SDUs must be delivered in order. When set to Yes, this attribute ensures that SDUs are delivered to higher layers in sequence.
UMTS RACH QoS to ASC Mapping Map the QoS classes to RACH access service classes available in the current cell.
UMTS RLC Processing Time Specify the Reliable Link Control processing time, which is primarily due to software processing and information transfer within nodes. The default value is15ms for uplink and downlink communication. (modeled on 3G TR 25.853)
UMTS UE Cell State Specify the state the UE is in, CELL_FACH or CELL_DCH.

Node-B Attributes

Table 242: Node-B Attributes

Use This Attribute… To…
Serving RNC ID Specify ID of the RNC in the scenario that acts as its network controller.
UMTS CPICH Transmission Power Specify the transmission power of the Node-B common pilot channel in Watts. This is a key parameter of cell evaluation (and consequently handover procedures).
UMTS Cell ID Specify an identifier for the Node-B and the cell that it is associated with, which can be useful to identify the cells in the debugger.
UMTS Cell Pathloss Parameters Specify the environment around the Node-B. The environment settings determine how the model computes cell pathloss. (Based on UMTS 30.03 TR 101 V3.2.0)
Shadow Fading Standard Deviation
(sub-attribute of UMTS Cell Pathloss Parameters)
Specify the standard deviation of the log normal distribution used to model shadow fading of the antenna signal. Typical attribute values are 12dB for indoor environments and 10dB for outdoor and vehicular environments.
Pathloss Model
(sub-attribute of UMTS Cell Pathloss Parameters)
Specify the surrounding environment (Vehicular, Pedestrian, Indoor Office,...), which defines the path loss model used for the cell.
Number of Floors
(sub-attribute of UMTS Cell Pathloss Parameters.
specify the number of floors when using Indoor office Environment in the Pathloss Model. Set this attribute to Not Used for other path loss models.
UMTS FACH Transmission Power Specify the FACH transmission power of the surrounding Node-B. The FACH transmission power can be explicitly configured in watts or it can be computed as distance-based to cover an imaginary circle of the specified radius around the Node-B.

RNC Attributes

Table 243: RNC Attributes

Use This Attribute… To…
RNC ID ID of the RNC on the UTRAN. In order for a Node-B to communicate with this RNC over a network connection, it is necessary to set the Serving RNC ID on the Node-B to this RNC's ID.
UMTS RNC Handover Parameters Configure the RNC to support hard or soft handovers and the parameters used in handover decisions. Based on TR 25.922.
UMTS RNC Admission Control Parameters Specify parameters (such as uplink and downlink loading factors and maximum available power) used to compute uplink and downlink capacity in the admission control algorithm.
UMTS RNC Timers Configure RNC Timers
Processing Time
(sub-attribute of UMTS RNC Timers)
Specify how long packets are delayed for processing at the RNC. This attribute does not include the time required for buffering on a transmission time interval. (Based on 3GPP TR 25.853)
Tinactivity (Data Channel)
(sub-attribute of UMTS RNC Timers)
Specify the maximum length of time a radio bearer can be inactive before it is released.
Tinactivity (Signaling Channel)
(sub-attribute of UMTS RNC Timers)
Specify the maximum length of time a radio signal can be inactive before it is released.
Tqueuing
(sub-attribute of UMTS RNC Timers)
Specify the maximum time a RAB assignment for setup can be queued during admission control. If the assignment is not served within this time, it is discarded.
UMTS RNC Channel Configuration Configure dedicated, common, and shared transport channels carrying data and signaling traffic. For data channels, you can configure channel parameters for each UMTS service class. The main transport channel attributes are described below. Note that the configurable transport channel parameters depend on the channel type. For example, RB Mapping info does not apply to common channels because it is specified on a per-UMTS-class basis for the UEs in CELL_DCH state.
RLC Info
(sub-attribute of UMTS RNC Channel Configuration Signaling Channel Config)
Configure parameters for radio link control operations.
UL RLC Mode and DL RLC Mode
(sub-attributes of RLC Info)
Specify the RLC mode used on the uplink (UL) and downlink (DL) channels. Because retransmissions triggered by TCP can incur larger delay in the unacknowledged mode, using an RLC in the acknowledged mode may reduce response times when TCP is running over a noisy channel.
Transmission Window Size and Receiving Window Size
(sub-attributes of RLC Info)
Specify the number of RLC PUs that can be sent or received without an acknowledgement. This attribute applies only to the RLC Acknowledged Mode.
RLC Discard Info
(sub-attribute of RLC Info)
Specify the timers used to determine when and how packets in the transmitter's RLC buffer are discarded.
In-Sequence Delivery
(sub-attribute of RLC Info)
Specify if the RNC preserves the order of packets received from higher layers. When this attribute is set to "No", the RNC forwards packets to the SGSN as they are received. When this attribute is set to "Yes", the RNC will only send packets to the SGSN in sequenced order. That is, if the RNC receives packet 21 but has not received packet 20, it will hold packet 21 until it receives and forwards packet 20 to the SGSN or until it realizes that packet 20 will never be fully received and sent to the SGSN.
DL RLC Status Info
(sub-attribute of RLC Info)
Specify how often downlink status reports are sent from the RNC to the CN. When the Missing PU Indicator sub-attribute is set to True, status reports are sent out each time a missing PU is detected, subject to the maximum and minimum intervals permitted between status reports. These maximum and minimum values are specified by the Timer Status Periodic and Timer Status Prohibit sub-attributes, respectively.
Timer Status Prohibit
(sub-attribute of DL RLC Status Info)
Specify how often the RNC checks to see if it should send status reports to the UEs. Once the time specified by this attribute has elapsed, the RNC determines if it needs to send status reports to UEs. If a status report is required, the RNC sends the report and resets this timer.
Missing PU Indicator
(sub-attribute of DL RLC Status Info)
Specify if a missing PU triggers the RNC to send a status report to the UEs. After the Timer Status Prohibit timer elapses, the RNC checks to see if a missing PU was detected. When this attribute is set to "True", the RNC will send a status report to the appropriate UEs if it detects a missing PU. When this attribute is set to "False", missing PUs do not trigger a status report.
Timer STATUS Periodic
(sub-attribute of DL RLC Status Info)
Define how often the RNC sends status reports to UEs if it detects missing PDUs. The RNC starts this timer when it receives its first AM packet and the timer is continually reset after expiration. Upon detection of a missing PDU, this timer triggers a status report to be sent at the end of the current Timer Status Prohibit timer.
RB Mapping Info
(sub-attribute of Transport channel Parameters)
Configure the parameters required to map the radio bearers to different channel types for the UEs that are in CELL_DCH state. The radio bearers for UEs in CELL_FACH state are mapped to FACH and RACH for down link and uplink, respectively.
UL TrChnl Info and DL TrChnl Info
(sub-attribute of Transport channel Parameters)
Define parameters required to compute the channel data rate from the information rate based on the channel coding employed. Currently, the model supports convolutional channel coding types, with puncturing.
UMTS to ATM QoS Mapping Define the QoS of each ATM SVC that carries a particular class of UMTS traffic.
Scheduling Weights Assign weights to each QoS class for use in the FACH's weighted round-robin scheduling algorithm.
UE ID Type Specify the format of the UE identification number used over FACH communications. Both C-RNTI (16-bit) and U-RNTI (32-bit) are supported.
AICH Transmission Timing Set the timing relation between PRACH and AICH channels.
ASC Parameters Configure the RACH access service classes that define the level of service for RACH procedures.

CN Attributes

Table 244: CN Attributes

Use This Attribute… To…
UMTS CN ID Define the CN identifier, which is used by IP Auto-Addressing to ensure that the UEs connected to this CN are in the same IP subnet. All nodes bearing the same CN ID or UE CN ID are assigned to the same IP subnet. Note that each CN must have a unique CN ID.
UMTS CN Timers Specify timers used in the operation of the CN.
T3350
(sub-attributes of UMTS CN Timers
Specify the length of the GPRS attach timer.
TRABAssgt
(sub-attributes of UMTS CN Timers
Specify the length of the RAB assignment timer.
T3385
(sub-attributes of UMTS CN Timers
Specify the length of the PDP activation timer.
T3386
(sub-attributes of UMTS CN Timers
Specify the length of the retransmission timer for MODIFY PDP CONTEXT request.
Processing Time
(sub-attributes of UMTS CN Timers
Specify the processing time for data services, transcoding, and so on.
Maximum Retry on Timer Expiry
(sub-attributes of UMTS CN Timers
Specify the maximum number of times a signaling message is sent after the RAB assignment timer expires.

Repeater Attributes

Table 245: Repeater Attributes

Use This Attribute… To…
Donor Node-B Cell ID Specify Node-B cell to which repeater has directional link. Required to associate repeater with its donor Node-B cell.
Downlink Gain Specify repeater gain (amplification) of a signal from Node-B to UE.
Downlink Packet Loss Ratio Specify probability used to determine if a packet is dropped while going from Node-B to repeater.
Max Downlink Transmit Power Specify maximum transmit power from repeater to UE.
Max Uplink Transmit Power Specify maximum transmit power from repeater to Node-B. (Used to calculate interference with other UE packets received at Node-B.)
Node-B Connection Technology Specify type of link used between repeater and its donor Node-B. Can be either a directional radio link (Air) or an optical fiber link (Fiber.) Impacts interference calculation at Node-B.
Noise Figure Specify magnitude of noise generated by repeater.
Uplink Gain Specify repeater gain (amplification) of a signal from UE to Node-B. (Used to calculate interference with other UE packets received at Node-B.)
Uplink Packet Loss Ratio Specify probability used to determine if a packet is dropped while going from repeater to Node-B.

本站文档由 北京智网畅联科技有限公司 整理、翻译并提供 · Documentation compiled and provided by Beijing ZNetLink Technology Co., Ltd.

交流群 · QQ Group:OPNET/智网妙算网络仿真交流群(群号 486383494)

原文档 © 2017 Riverbed Technology · 本站为公益翻译,由 AI 辅助完成,请仔细甄别

Original documentation © 2017 Riverbed Technology. Community translation, AI-assisted. Contact: jiazequn@znetlink.com