BGP-Based VPLS and Layer-2 VPNs

BGP-based VPLS and Layer-2 VPNs are configured on service provider core routers (P) and service provider edge routers (PE). Configuring BGP-based VPLS and Layer-2 VPNs consists of three main steps:

  1. Create a tunnel LSP between PE routers
  2. Configure an IGP on PE and P routers
  3. Configure an IBGP session between PE routers

Creating Tunnel LSPs Between PE Routers

Tunnel LSPs are point-to-point interconnections between PE routers that aggregate and transfer individual customer traffic. Before creating tunnel LSPs, you first need to enable MPLS on all router interfaces.

Procedure 90: Enabling MPLS on all Interfaces Between PE and P Routers

  1. Enable the following attributes on all routers and router interfaces between the PE and P routers.
    • MPLS > MPLS Parameters > Status
    • MPLS > MPLS Parameters > Interface Information > Status

End of Procedure 90

Enabling LDP or RSVP-TE to Create Tunnel LSPs

There are two ways to create LSPs when analyzing VPLS or Layer-2 VPNs. The LSPs can be LDP-based paths or you can create traffic engineered LSPs manually.

Procedure 91 describes the steps needed to enable the creation of LDP-based paths in the network.

Procedure 91: Configuring LDP-Based Paths

  1. Enable the following attributes on all P and PE routers.
    • MPLS > LDP Parameters > Status
    • MPLS > LDP Parameters > Interface Information > Status

End of Procedure 91

Dynamic/Static LSPs

You can configure dynamic or static LSPs between PE routers, which use RSVP-TE or CR-LDP for signaling. For VPLS, PE routers should have a full-mesh of dynamic LSPs. For Layer-2 VPNs, the dynamic LSPs depend upon a point-to-point connection between PE routers. See Procedure 78, Procedure 79 or Procedure 80 for details on configuring dynamic LSPs.

Configuring an IGP on PE and P routers

For Layer-2 VPNs and VPLS to work properly, the PE and P routers should be able to exchange routing information. You must configure an IGP or static routes between these routers. If you configured dynamic or static LSPs to create tunnel LSPs, you must configure OSPF or IS-IS as the IGP.

For label exchanges to occur, an IBGP session needs to be configured between the PE routers. The following configuration needs to be done:

Procedure 92: Configuring an IBGP Session Between PE Routers

  1. Set the IP Routing Parameters > BGP Parameters > Address Family attribute to L2VPN. This lets BGP neighbors exchange labels in the BGP advertisements.

  2. Set the IP Routing Parameters > BGP Parameters > Address Family Properties > Status attribute to Enabled.

  3. Configure the IP Routing Parameters > BGP Parameters > Address Family Properties > Neighbor Information attribute so that it includes an entry for the other PE routers. The IP Address should be the address of the loopback interface of the neighboring PE router.

  4. Set the Send-Community attribute to Enabled.

End of Procedure 92

Configuring Layer-2 VPNs

This section describes the configuration needed for BGP-based Layer-2 VPNs. This configuration is done on PE routers.

Procedure 93: Configuring Layer-2 VPNs

  1. Create a L2VPN instance in VPN > Network Based > L2VPN/VPLS Instances > BGP Based > Instance Information.

  2. Set the Instance Type to L2VPN.

  3. Configure the Route Target, Route Distinguisher, and Site Information attributes.

  4. Associate the interface on the PE router with the L2VPN instance on which the router receives traffic from the customer.

  5. Set the Status to enabled.

  6. Configure the Site Name and Remote Site ID attributes.

End of Procedure 93

Configuring VPLS

This section describes configuration required for BGP-based VPLS on PE routers.

Procedure 94: Configuring VPLS

  1. Create a VPLS instance in VPN > Network Based > L2VPN/VPLS Instances > BGP Based > Instance Information. Make sure the Instance Type is set to VPLS.

  2. Configure the Route Target, Route Distinguisher, and Site Information attributes.

  3. Associate the interface on PE router with the VPLS instance on which the router receives traffic from the customer.

  4. Set the Status to Enabled.

  5. Set the Site Name. Make sure that Leave Remote Site ID is set to Not Configured.

End of Procedure 94

本站文档由 北京智网畅联科技有限公司 整理、翻译并提供 · Documentation compiled and provided by Beijing ZNetLink Technology Co., Ltd.

交流群 · QQ Group:OPNET/智网妙算网络仿真交流群(群号 486383494)

原文档 © 2017 Riverbed Technology · 本站为公益翻译,由 AI 辅助完成,请仔细甄别

Original documentation © 2017 Riverbed Technology. Community translation, AI-assisted. Contact: jiazequn@znetlink.com