EPS Bearer Definitions
An Evolved Packet System (EPS) bearer is a transmission path of defined quality, capacity, delay, and so on. The following describes support for EPS bearer definitions in the LTE model:
- Up to eight EPS bearers, including the Default bearer, per User Equipment (UE), are supported
- At a minimum, each UE has one non-guaranteed bit rate (Non-GBR) type EPS bearer, which is called the Default bearer
- The Default bearer is established as soon as the UE gets attached to an Evolved Packet Core (EPC)
- Higher layer traffic that could not be mapped to any of the configured EPS bearers is served by the Default bearer
- The following parameters are used to define the EPS bearers and are configurable in the following attribute: LTE Config Node > EPS Bearer Definitions.
- Allocation Retention Priority (ARP) – Used by admission control for GBR bearers only
- Uplink/Downlink Guaranteed Bit Rate (GBR) – For GBR bearers only
- Scheduling Mechanism – Used for GBR bearers to specify the type of scheduling: Dynamic or Semi-Persistent Scheduling. A UE can have a maximum of one EPS bearer that is using semi-persistent scheduling.
- QoS Class Identifier (QCI) – Associates the bearer with a QoS Class Definition. QoS Class Definitions consist of three parameters: bearer (resource) type, L2 packet delay budget, and L2 packet loss budget. The QCI corresponding to each QoS Class Definition is as follows:
Table 140: Standardized QCI Characteristics¹
| QCI | Resource Type | Priority | Packet Delay Budget | Packet Error Loss Rate | Example Services |
|---|---|---|---|---|---|
| 1 | GBR | 2 | 100 ms | 10⁻² | Conversational Voice |
| 2 | 4 | 150 ms | 10⁻³ | Conversational Video (live streaming) | |
| 3 | 3 | 50 ms | 10⁻³ | Real-Time Gaming | |
| 4 | 5 | 300 ms | 10⁻⁶ | Non-Conversational Video (buffered streaming) | |
| 5 | Non-GBR | 1 | 100 ms | 10⁻⁶ | IMS Signaling |
| 6 | 6 | 300 ms | 10⁻⁶ | Video (Buffered Streaming) TCP-based (e.g., web, e-mail, chat, FTP, point-to-point file sharing, progressive video, etc.) |
|
| 7 | 7 | 100 ms | 10⁻³ | Voice Video (Live Streaming) Interactive Gaming |
|
| 8 | 8 | 300 ms | 10⁻⁶ | Video (Buffered Streaming) TCP-based (e.g., web, e-mail, chat, FTP, point-to-point file sharing, progressive video, etc.) |
|
| 9 | 9 |
Note 1: Source: 3GPP TS 23.203 “Policy and charging control architecture”
The bearer type parameter has two values: GBR and non-GBR. GBR bearers have minimum rate guarantees and are required to go through admission control when their radio bearers are created. Non-GBRs are best effort bearers with no resource guarantees at all.
The L2 Packet Delay Budget (L2PDB) parameter describes the maximum time that packets shall spend transiting through radio link control (RLC) and MAC layers within the network and the terminal. It shall be interpreted as a maximum delay with a confidence level of 98 percent. This parameter is applicable only for GBR bearers.
The L2 Packet Loss Rate (L2PLR) parameter describes the maximum ratio of Layer-2 packets that have not been successfully delivered to the peer entity. This parameter is not supported in LTE simulations.
-
Values of the EPS bearer parameters listed in this section are among the inputs used by eNodeB schedulers. The parameter values are also inherited by other entities mapped to a given EPS bearer across different sublayers in the LTE system as required (for example, radio bearers and logical, transport, and physical channels).
-
The LTE model assumes that complete configurations of all the EPS bearers of the UEs are known by the LTE core network at the beginning of the simulation. Therefore an EPC node will always be able to identify the EPS bearer of arriving downlink data traffic even if that bearer is inactive at that moment and was never activated.
-
An EPS bearer and its radio and S1 bearers are created when that EPS bearer has at least one active service data flow (SDF). Note the following:
- Higher layer data packets are queued while the bearers are being created
- Non-GBR EPS bearers are not destroyed or deactivated once they are created
- Requests for radio bearers of GBR EPS bearers go through the admission control procedure, since there will be a certain amount of cell resources reserved for those bearers.
Data flow activity through GBR EPS bearers is monitored. If a bearer becomes inactive for a certain period (configurable via the LTE > Admission Control Parameters > Inactive Bearer Timeout attribute on the eNodeB), then its radio bearer is torn down and the cell resources reserved for it are released. This makes the EPS bearer inactive. When the EPS bearer has at least one active SDF again, then it is re-activated.
If the request to create a radio bearer for a GBR EPS bearer is rejected by admission control, then queued packets of that EPS bearer are flushed (unless they are switched to the Default bearer). Later, if any of that bearer's SDF becomes active again, the radio bearer creation procedure is re-initiated.
Preemption by admission control is also modeled. When the cell is congested, GBR radio bearers with high ARP (low priority) are preempted if that is necessary and sufficient to accept a radio bearer request for an EPS bearer with a low ARP (high priority).
When the link adaptation procedure changes the MCS index of the UE based on channel conditions, and if the magnitude of this change exceeds a threshold, resources required by the active GBR bearers of that UE are reevaluated by the admission control entity of its eNodeB. If the new MCS index is lower, the resources needed by the active GBR bearers of that UE to guarantee the quality of service required by those bearers may no longer be available in the cell under current load conditions. In that case, the eNodeB may release the bearers, using a procedure similar to releasing a bearer during inactivity or preemption.
Key Concept— In regard to the implications of reevaluation: (1) One or more lower priority bearers are preempted if the reevaluated bearer requires more cell resources. (2) The reevaluated bearer is released if there are not enough resources to sustain the bearer.
EPS bearers are considered bidirectional. The values of the EPS bearer parameters that do not have a type of “bit rate” are taken into account for both directions. On the other hand, there will be separate values specified for the GBR and maximum bit rate (MBR) parameters for uplink and downlink.