Menu Operations: IP
The model includes several menu operations to facilitate the task of configuring IP in your network model. Many of these operations allow you to configure IP model attributes on several nodes in a single step. For example, the “Configure Dynamic Routing Protocols…” menu operation configures the IP > IP Routing Parameters > Interface Information > Routing Protocols attribute on multiple interfaces. Each IP menu operation is briefly described below. If you require more detailed information about the effects of a particular configuration, see the description of the corresponding attribute in Model Attributes: IP section.
The following operations are available from the Protocols > IP menu.
Table 107: IP Menu Operations
| Menu Item | Description |
|---|---|
| IP > Addressing | IP addressing operations. Note: IP address assignment menu operations assign an IP address to physical and loopback interfaces only. Clear IP address menu operations clear all IP addresses from all interfaces including subinterfaces, tunnel interfaces, VLANs, and all secondary addresses of any interface type. |
| Auto-Assign IP Addresses… | Opens a dialog box in which you can specify options for assigning IP addresses to interfaces in the network. The dialog box allows you to choose the following options: - Assign IPv4 addresses only or IPv6 addresses only or both IPv6 Addresses. You can choose to assign addresses to all interfaces or just to router interfaces. If you choose to assign to router interfaces, then hosts learn their addresses from routing advertisements. This is known as stateless address auto-configuration. EUI-64 Format. You can choose to assign IPv6 addresses in the EUI-64 format or non-EUI-64 format. In the EUI-64 format, only the network prefix is assigned to the interface and the host component of the address is automatically computed by the interface. This format is an IEEE standard. If the non-EUI-64 option is chosen, then the entire IPv6 address (128 bits) are configured on the interfaces. Disable IPv4. You can choose to disable IPv4 on the interfaces on which IPv6 addresses are being configured. If this option is selected, the IPv4 address is set to “No IP Address.” This ensures that the node can communicate using IPv6 only. |
| Auto-Assign IPv4 Addresses | A shortcut to assign IPv4 addresses to all interfaces in the network model. |
| Clear IP Addresses… | Opens a dialog box in which the following options can be specified for clearing addresses: - Clear IPv4 only, IPv6 only or both - Clear all interfaces - Clear selected interfaces - Clear unattached interfaces |
| Clear IP Addresses of All Interfaces | Deletes any explicit IPv4 or IPv6 address configuration by setting the IP address of all nodes in the network to the value Auto Assigned. |
| Clear IP Addresses of Unattached Physical Interfaces | Deletes any explicit IPv4 or IPv6 address configuration by setting the IP address of all unconnected interfaces in the network to Auto Assigned. |
| Clear IP Addresses for Selected Nodes and Interfaces | Deletes any explicit IPv4 or IPv6 address configuration by setting the IP address of the interfaces of the selected nodes and links to Auto Assigned. |
| Configure AS Number for Selected Routers... | Configures a selected router with an Autonomous System (AS) number. |
| Clear AS Number Specification... | Clears either the selected routers or all routers of their specified AS numbers. |
| Auto-Assign Router IDs | Assigns a router ID to every router in the network model. |
| Clear Router IDs on All Routers | Clears the router ID from every router in the network model. |
| Configure Router ID as Loopback Address… | Assigns the router ID configured on the node to be its loopback address with a /32 subnet mask. Ignores auto-assigned IDs. |
| Select Node with a Specified IP Address… | Finds and selects the node in the network topology that has been configured with a particular IP address. This operation works for manually and automatically assigned IP addresses. |
| IP > Routing | IP routing operations |
| Configure Routing Protocols… | Specifies dynamic routing protocols used on all interfaces of the selected routers or on the interfaces connected to the selected link. |
| Configure Routing Protocols on Loopback Interfaces… | Specifies the dynamic routing protocols running on the loopback interfaces of the selected routers or all routers in the network. |
| Enable Reachability Analysis | A toggle that enables or disables the reachability analysis feature. |
| Reachability Analysis | Displays next hop on all routers for a specified IP address based on information from Flow Analysis or Discrete Event Simulation. Useful for checking route propagation for routing failures or what-if scenarios. Must be enabled with “Enable Reachability Analysis”. |
| Export Routing Tables... | Configures the specified routers to export their routing table in subsequent simulations. You can specify “all routers” or “selected routers” in the dialog box that displays. |
| Configure Multipath Routes Threshold… | Specifies the maximum number of multipath routes stored in the routing tables of the selected routers. |
| Configure Interface Metric Information… | Specifies the bandwidth and delay used in metric computations on the selected interfaces. |
| Configure Load Balancing Option… | Configures all or selected routers to use either packet-based or destination-based load balancing. |
| Forwarding Table Comparison | Opens the IP Forwarding Table Comparison dialog box, which lets you compare forwarding tables between the Operational Network, DES, or Flow Analysis. You must have forwarding tables from at least two sources to use this feature. See Analyzing IP Forwarding Tables for more information about this feature. If you want to validate routing in your network, see also “Validating Simulated Routing Against Operational Data” on page 103. |
| View Route Comparison Reports | Displays selected Route Comparison reports after a Forwarding Table Comparison has been run. |
| View Route Comparison Log | Displays the log from all Forwarding Table comparisons. |
| IP > Interfaces | IP interfaces operations |
| Create Loopback Interface… | Configures all or selected routers with a loopback interface, if none exists. You can also configure routing protocols through this option by selecting the “Configure routing protocols” checkbox on the Create Loopback Interface dialog box. |
| Create Sub-interfaces for selected ATM/FR PVXs | Creates sub-interfaces on physical interfaces on the nodes at either end of the PVX; ties the sub-interface with the PVX via the Layer-2 mapping specification. |
| IP > Demands | IP demands operations |
| Characterize Traffic Demands… | Configures IP background traffic characteristics (such as ToS, packet size, and packet interarrival) for traffic flows. |
| Configure Start Time… | Configure the start time for which traffic will be initiated for a specific demand or all demands. |
| Display Routes for Configured Demands… | Shows the routes taken by traffic flows in the network. |
| Hide Routes… | Hides the routes taken by conversation pair traffic flows in the network. |
| Visualize Routability of IP Flows (Flow Analysis) | Used to visualize successful and failed demands (routable and unroutable demands) after a Flow Analysis run. Successful demands are colored green and failed demands are colored red. |
| Clear Routability Visualization | Restores the visualized demands back to their original color. |
| Configure Ping Traffic on Selected Nodes… | Creates ICMP ping traffic between all or currently selected nodes in the network. Ping traffic created using this operation is added to any existing traffic. Do not use this operation to edit ping traffic—use the “Clear Ping Traffic” operation to delete existing traffic, then use this operation (Configure Ping Traffic on Selected Nodes…) to re-create the traffic. Note the following: - Ping traffic is supported for discrete event simulation only. Flow analysis does not recognize ICMP ping traffic. - In the “Ping Traffic Details” the “Record Route” pattern is the default. This pattern will cause the path of each ping to be recorded in the simulation log. Alternatively, you can choose “New...” from the drop-down menu of the “Pattern” field and configure specific attributes of the ping pattern you want to use. - Support is provided for both IPv4 and IPv6. For information about creating ping demands manually, see Configuring Ping Traffic. |
| Clear Ping Traffic… | Deletes all ICMP ping traffic on all or selected nodes in the network. |
| IP > QoS | IP quality of service operations |
| Configure QoS | Specify QoS scheme and profile to be applied to selected link(s) or router(s) or to all connected interfaces. |
| IP > Multicast | IP multicast operations |
| Enable Multicasting on Selected Hosts | Enables multicast on selected hosts |
| Enable Multicasting on Interfaces Across Selected Links | Enables multicast on selected router interfaces |
| Set Multicast Group on Selected Destination Nodes... | Specify a join and leave time for a specified Multicast group and application to be applied to the selected destination node |
| Set IGMP Membership Groups on Selected Routers... | Configures a specified multicast group on all or selected routers. |
| Enable Auto-RP on Selected Routers | Configures Auto-RP on selected routers. |
| Configure Rendezvous Point Using Static RP Configuration... | Configures a rendezvous point with a specified static address for a specified multicast group. You can apply the configuration to all or a selected group of routers. |
| Model User Guide | Opens the IP Multicast model user guide. |
| IP > Configuration Reports | Configuration report generation. |
| Select/Generate... | Generates reports that you specify in the pick list. |
| Generate All | Generates all configuration reports. |