Route Redistribution
Each routing protocol works independently to maintain its own routing information. IP works in conjunction with each of these protocols to remain informed about the proper routes to use for each possible destination network. In general, a particular routing protocol prevails within given areas of the network. At the border between areas with distinct routing protocols, a function called “route redistribution” take place so that routes can be learned among the protocols. You can enable redistribution on a per-protocol basis by choosing “Configure Route Redistribution...” from the Protocols > <protocol_name> menu.
Unless metrics have been explicitly defined in the device configuration files for imported devices or manually (using the Protocols menu operation or directly in the Redistribution attribute), the following default metrics are used for redistribution. In Table 105, “None” indicates that redistribution does not occur—even if redistribution is enabled.
Table 104: Default Redistribution Metrics for all Routers (Except Juniper)
| Redistribution Into | |||||
|---|---|---|---|---|---|
| BGP | EIGRP/IGRP | ISIS | OSPF | RIP | |
| BGP | n/a | none | 0 | 1 | none |
| EIGRP/IGRP | same as RP¹ | native metric | 0 | 20 | none |
| ISIS | same as RP¹ | none | same as RP¹ | 20 | none |
| OSPF | same as RP¹ | none | 0 | same as RP¹ | none |
| RIP | same as RP¹ | none | 0 | 20 | same as RP¹ |
| Connected | 0 | formula² | 0 | 20 | 0 |
| Static | 0 | 256/1 | 0 | 20 | 0 |
Note 1: Same as redistributed protocol.
Note 2: There is a factor of 256 between IGRP and EIGRP in the composite metric computation.
Table 105: Default Redistribution Metrics for Juniper Models
| Redistribution Into | |||||
|---|---|---|---|---|---|
| BGP | EIGRP/IGRP | ISIS | OSPF | RIP | |
| BGP | n/a | n/a | 10 | same as RP¹ | 1 |
| EIGRP/IGRP | n/a | n/a | n/a | n/a | n/a |
| ISIS | same as IGP² | n/a | same as RP¹ | same as RP¹ | 1 |
| OSPF | same as IGP² | n/a | same as RP³ | same as RP¹ | 1 |
| RIP | same as IGP² | n/a | same as RP¹ | same as RP¹ | same as RP¹ |
| Connected | 0 | n/a | 10 | 0 | 1 |
| Static | 0 | n/a | 10 | 0 | 1 |
Note 1: Same as redistributed protocol.
Note 2: Same as IGP route metric.
Note 3: Same as redistributed protocol (max 63)
Default Interface Information for Cisco Routers
The following parameters (bandwidth, delay, MTU, reliability, load) are used to compute the default metric when redistributing directly connected interfaces into EIGRP/IGRP. Bandwidth and delay are dependant on the interface type.
Table 106: Default Values for Calculating Redistribution Into EIGRP/IGRP
| Bandwidth (Mbps) | Delay (µsec) | MTU (bytes) | Reliability | Load | |
|---|---|---|---|---|---|
| Eth/Fasteth/Giga | 10/100/1,000 | 1,000/100/10 | 1,500 | 255 | 255 |
| FDDI | 100 | 100 | 4,470 | 255 | 255 |
| Token Ring | 4/16 | 100 | 4,464 | 255 | 255 |
| ATM | 25 | 80 | 4,470 | 255 | 255 |
| FR | 1.544 | 20,000 | 1,500 | 255 | 255 |
| IP | 1.544 | 20,000 | 1,500 | 255 | 255 |
| Loopback | 8,000 | 5,000 | 1,514 | 255 | 255 |
| Tunnel | 0.9 | 500,000 | 1,514 | 255 | 255 |
| VLAN | 10 | 1000 | 1,500 | 255 | 255 |