The “None” Pipeline Stage
If some of the pipeline stages are not important to the goals of your simulation, you can skip these stages. To skip a pipeline stage, assign “NONE” to the pipeline stage attribute in a transmitter or receiver module. During simulation, the Simulation Kernel skips each stage set to “NONE” and sets the corresponding TDA to a default value in place of a calculated result. The following table lists the default values used by the Radio Transceiver Pipeline.
Table 68: Radio Transceiver Pipeline Default Values
| Pipeline Stage | TDA | Default Value |
|---|---|---|
| 0: Receiver Group | none | empty receiver group ¹ |
| 1: Transmission Delay | OPC_TDA_RA_TX_DELAY | 0 seconds |
| 2: Link Closure | OPC_TDA_RA_CLOSURE | OPC_TRUE |
| 3: Channel Match | OPC_TDA_RA_MATCH_STATUS | OPC_TDA_RA_MATCH_VALID |
| 4: Transmitter Antenna Gain | OPC_TDA_RA_TX_GAIN | 0 dB |
| 5: Propagation Delay | OPC_TDA_RA_START_PROPDEL OPC_TDA_RA_END_PROPDEL |
0 seconds 0 seconds |
| 6: Receiver Antenna Gain | OPC_TDA_RA_RX_GAIN | 0 dB |
| 7: Received Power | OPC_TDA_RA_RCVD_POWER | (transmitter power) times (transmitter antenna gain) times (receiver antenna gain) ² |
| 8: Interference Noise | none | no interference with other packets |
| 9: Background Noise | OPC_TDA_RA_BKGNOISE | 0 watts |
| 10: Signal-to-Noise Ratio | OPC_TDA_RA_SNR | 1000 dB ³ |
| 11: Bit Error Rate | OPC_TDA_RA_BER | 0 |
| 12: Error Allocation | OPC_TDA_RA_NUM_ERRORS OPC_TDA_RA_ACTUAL_BER |
0 OPC_TDA_RA_BER |
| 13: Error Correction | OPC_TDA_RA_PK_ACCEPT | OPC_TRUE |
Note 1: Same behavior as using the dra_no_rxgroup model.
Note 2: Calculated as OPC_TDA_RA_TX_POWER × 10^OPC_TDA_RA_TX_GAIN × 10^OPC_TDA_RA_RX_GAIN.
Note 3: Arbitrary very large value, equivalent to no noise.
You can change the default value assigned by a NONE pipeline stage by setting the value of the corresponding simulation preference, as listed in Table 69.
Table 69: Simulation Preferences for Radio TDA Defaults
| Pipeline Stage | TDA | Simulation Preference |
|---|---|---|
| 0: Receiver Group | none | none |
| 1: Transmission Delay | OPC_TDA_RA_TX_DELAY | psnone_tda.ra.txdel.tx_delay |
| 2: Link Closure | OPC_TDA_RA_CLOSURE | psnone_tda.ra.closure.closure |
| 3: Channel Match | OPC_TDA_RA_MATCH_STATUS | psnone_tda.ra.chanmatch.match_status |
| 4: Transmitter Antenna Gain | OPC_TDA_RA_TX_GAIN | psnone_tda.ra.tagain.tx_gain |
| 5: Propagation Delay | OPC_TDA_RA_START_PROPDEL OPC_TDA_RA_END_PROPDEL |
psnone_tda.ra.propdel.start_propdel psnone_tda.ra.propdel.end_propdel |
| 6: Receiver Antenna Gain | OPC_TDA_RA_RX_GAIN | psnone_tda.ra.ragain.rx_gain |
| 7: Received Power | OPC_TDA_RA_RCVD_POWER | psnone_tda.ra.power.rcvd_power ¹ |
| 8: Interference Noise | none | none |
| 9: Background Noise | OPC_TDA_RA_BKGNOISE | psnone_tda.ra.bkgnoise.bkgnoise |
| 10: Signal-to-Noise Ratio | OPC_TDA_RA_SNR | psnone_tda.ra.snr.snr |
| 11: Bit Error Rate | OPC_TDA_RA_BER | psnone_tda.ra.ber.ber |
| 12: Error Allocation | OPC_TDA_RA_NUM_ERRORS OPC_TDA_RA_ACTUAL_BER |
psnone_tda.ra.error.num_errors psnone_tda.ra.error.actual_ber |
| 13: Error Correction | OPC_TDA_RA_PK_ACCEPT | psnone_tda.ra.ecc.pk_accept |
Note 1: Values greater than or equal to 0.0 are used as-is. Values less than 0.0 result in the default computation of OPC_TDA_RA_TX_POWER × 10^OPC_TDA_RA_TX_GAIN × 10^OPC_TDA_RA_RX_GAIN.