Model Features: Wireless LAN

The model implements the following protocol features.

Table 264: Wireless LAN Model Features

Model Feature Description
Access mechanism Carrier sense multiple access and collision avoidance (CSMA/CA) distributed coordinating function (DCF) access scheme is modeled as defined in the standard. DCF provides a contention-based access mechanism that includes Exponential back-off with reduced collision probability.

The point coordination function (PCF) access scheme, which offers contention-free access mechanism and can be used in infrastructure network configurations, is also supported.
Hybrid Coordination Function (HCF) The model supports Enhanced Distributed Channel Access (EDCA) with the following characteristics:
- Four Access Categories (ACs) for prioritized contention-based access
- Voice, Video, Best Effort, and Background
- EDCA Parameter Set distribution by Access Point (AP)
- Transmission Opportunity (TXOP) Frame Bursting
- With HCF Capability or 802.11n enabled, an STA can transmit multiple frames in a TXOP if the value of the TXOP limit for the access category is greater than zero.
- While transmitting a frame in a TXOP, if there is time in the TXOP for the transmission sequence of the next MPDU in the queue, an STA reserves the medium by setting the duration field to account for the response frame of the current frame, the next frame, and its response frame.

Note: Exception to the rule above: In an HT-STA, if an access category (AC) has at least one traffic category for which A-MPDU is enabled, then the first frame in the TXOP reserves the medium for the entire TXOP duration, if there will still be time left in the transmission opportunity after the first frame transmission. Similarly, other frames in the TXOP reserve the medium for the remaining duration of the TXOP.
Frame exchange sequence Reliable data transmission is supported via threshold-based RTS-CTS exchange.
Fragmentation and reassembly Optional data frame fragmentation is supported based on the size of the data packet received from the higher layer. The fragments are reassembled at the destination station.
Access Point functionality A station can be configured as an access point in an infrastructure BSS network. All stations are capable of being an access point, however, only WLAN bridges, switches, or routers can connect a BSS to the distribution system—use these nodes when you are configuring an ESS.
Roaming Roaming can be enabled or disabled on Wireless LAN nodes. Roaming lets nodes connect to a better access point (AP) when the connection quality with their current AP drops below an acceptable level.

Note: Roaming is only supported for standard unlicensed channels (i.e., channels 1 to 11 for nodes operating in 2.4GHz frequency band with technologies 802.11b, 802.11g, and 802.11n [2.4GHz] and channels 36, 40, 44, 48, 52, 56, 60, 64, 149, 153, 157, and 161 for nodes operating in 5.0GHz frequency band with technologies 802.11a or 802.11n [5.0 GHz]). Roaming is also supported for 802.11p.
802.11p Roaming
For an 802.11p-capable WLAN node, that is not configured to always operate in 802.11p WAVE mode, to switch to and from 802.11p WAVE operation, roaming must be enabled.
Such a node will first operate in its configured PHY technology. If the node belongs to an infrastructure BSS, and then disconnects from its AP and cannot find another AP after scanning all the operational channels of its configured PHY technology once, then the node will switch to WAVE operation.
Periodically, the node will switch to its PHY technology and will scan all operational channels once. If an AP is found, the node will switch back to its PHY technology; otherwise it will continue in WAVE operation.
MAC-level Acknowledgements The model supports normal ACK, Block-ACK, and no-ACK MAC-level acknowledgement mechanisms. A MAC acknowledgement requirement can be configured separately for each traffic category.
BA support includes:
- BA agreement setup with exchange of action management frames
- Immediate BA and delayed BA
- BA support for roaming
- Inactivity detection and BA tear-down
802.11n MAC Features - Aggregated-MSDU (A-MSDU)
- Aggregated-MPDU (A-MPDU)
- No ACK, Immediate Block ACK and Delayed Block ACK are supported with unicast A-MPDU frames.
- Access Points can transmit broadcast A-MPDU frames
- Implicit block ACK requests will be used with Immediate Block ACK agreement
- Block ACK Enhancements:
- An HT-STA always supports Block ACK capability (If the STA is HT-STA, the value of the attribute WLAN Parameters > HCF Parameters > Block ACK Capability is ignored and is always considered “Enabled”.)
- A block ACK agreement between two HT-STAs uses the compressed BA frame.
- Data MPDUs belonging to a Block ACK agreement between two HT-STAs will not be fragmented.
- Immediate Block ACK agreement between two HT-STAs follows the HT-Immediate Block ACK architecture as recommended by the IEEE 802.11n standard.
- Only Full State mode of the scoreboard context is supported.
Physical Layer The following physical layer technologies are modeled:
- FHSS, IR, DSSS, OFDM, Extended Rate PHY-OFDM (802.11g), and High-Throughput PHY (802.11n)
- Auto-assignment of channels to BSSs (optional). If manually assigning channels, make sure that each WLAN node in a BSS uses the same channel.
HT PHY (802.11n)
802.11n operation is supported in both 2.4GHz and 5GHz frequency bands for 20MHz or 40MHz bandwidth. The following support is also included for HT:
- Support for 20MHz and 40MHz data rates
- 20/40MHz BSS Operation
- PPDU formats for 20MHz include HT-Mixed format and HT-Greenfield format
- PPDU formats for 40 MHz include Non-HT Duplicate PPDU format, HT-Mixed format, and HT-Greenfield format
- Short guard intervals, which allow higher data rates
- MIMO capability, which allows higher data rates; however the physical layer details of MIMO are not currently implemented
- Reduced inter-frame spacing (RIFS)
- Carrier sensing in secondary channel for 40MHz transmissions
Data Rates Supported Non-HT (non-802.11n) data rates (in Mbps)
1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54
Supported HT (802.11n) data rates (in Mbps)
6.5 (base) / 60 (max)
13 (base) / 120 (max)
19.5 (base) / 180 (max)
26 (base) / 240 (max)
39 (base) / 360 (max)
52 (base) / 480 (max)
58.5 (base) / 540 (max)
65 (base) / 600 (max)
Note: Given a base data rate, the effective 802.11n data rate can be increased by one of the following:
- Configuring more than one spatial stream (MIMO)
- Enabling short GI capability
- Enabling support for 40MHz operation
Supported WAVE (802.11p) data rates (in Mbps)
3, 4.5, 6, 9, 12, 18, 24, 27
Modulation The following modulations models are supported: DPSK, BPSK, QPSK, CCK-55, CCK-11, QAM-16, and QAM-64
Inter-operability Support The model supports interoperability with roaming between
- 11e capable and non-11e capable STAs
- 11b, 11g, and 11n capable STAs when operating at 2.4 GHz
- 11a and 11n capable STAs when operating at 5 GHz
- 11n STAs that support HT-Greenfield PPDU and 11n STAs that do not support HT-Greenfield PPDU
- 40MHz Capable HT STAs, non-40MHz capable HT STAs, and non-HT STAs
For example, an 11n STA may roam from a 11n AP to a 11g AP, which does not support 11e.
Protection Mechanisms
The model uses CTS-to-self or RTS/CTS protection mechanism to protect transmissions at 11g or 11n data rates in the presence of 11b STA.
One of the protection mechanisms listed in Table 9-8 of IEEE 802.11n-2009 Standard will be used to protect the following:
- Data frame transmissions at 11n data rates in the presence of 11g/11a STAs in the BSS
- Data frame transmissions at 11n data rates with HT-Greenfield header format in the presence of STAs that do not support HT-Greenfield header format in the BSS
- Data frame transmissions at 11n 40MHz data rates in the presence of STAs that do not support 40MHz data rates in the BSS
Communication Distance and Spatial Reuse The maximum communication distance between two WLAN nodes is a function of three parameters: the transmission power of the sending node, the path-loss propagation model, and the reception power threshold (receiver sensitivity) of the receiving node. Based on the configured values of these parameters, you can model WLAN networks in which the communication distance is more than 300 meters. The IEEE 802.11 standard limits the distance between WLAN nodes to 300 meters. Therefore, WLAN networks that extend beyond 300 meters might incur a performance degradation in the WLAN MAC algorithm.
The receiver sensitivity concept that is implemented through the reception power threshold attribute enables spatial reuse modeling with WLAN models. Packets with a reception power that is lower than the threshold cannot make the receiver lock onto their signal and will be treated as noise packets. When the signal of these packets is very weak, the receiver can simultaneously receive another packet with a strong signal from a nearby neighbor. This means that if two sets of WLAN nodes are far away from each other, they can act as two different LANs but still use the same BSS ID and frequency band (and therefore double the total available bandwidth).
IP auto-addressing IP auto-addressing is supported for WLAN nodes. All WLAN nodes in the same BSS are configured to belong to the same IP network. If there is a static assignment, that assignment will be the network address of all nodes in the subnet. If there is more than one static assignment and they have different network addresses, the first static assignment that is encountered becomes the network address of all the nodes in the subnet.

Note: Wireline and wireless nodes use different, independent procedures for auto-addressing.
Terrain Modeling Module The model supports Terrain Modeling Module. With Terrain Modeling Module, you can use any of the propagation models and terrain information included in Terrain Modeling Module. If Terrain Modeling Module is not used, the free space propagation model is used.
Mobile IP WLAN node models support Mobile IPv4 and Mobile IPv6.
Antenna patterns You can use the default antenna pattern, use one of the vendor antenna pattern, or use a custom antenna pattern with WLAN nodes.
Co-existence Support Interference between WLAN and ZigBee networks operating in overlapping bands is supported.