Model Features: HAIPE

The High Assurance Internet Protocol Encryptor (HAIPE) Interoperability Specification (IS) was developed by the US Department of Defense to ensure interoperability for IPsec encryption products. The HAIPE model supports features from all current versions (at the time this document was developed) of the HAIPE IS:

  • 1.3.5: Provided backward compatibility to TACLANE Classic/E100 devices in addition to a mode interoperable with other HAIPE 1.3.5 compliant devices.
  • 3.0: A derivative of IETF standards for IPsec and ESP. HAIPE 3.0 devices provide bandwidth-efficient transforms including support for tunnel and transport modes. HAIPE 3.0 devices are also backwards compatible to version 1.3.5 devices using less bandwidth (efficient mode).
  • 3.1: Added several enhanced networking features including Network Address Translation-Transversal (NAT-T), PT Reachability Advertisement, and Implicit Peer Discovery (IM-PEPD) as well as HAIPE-to-HAIPE Key Transfer.
  • 4.1: Added Internet Key Exchange (IKE) version 2, which allows certificate-based authentication and provides for bandwidth management; PT Robust Header Compression (RoHC); dynamic multicast group creation; and over-the-network keying.

The HAIPE model implements the features shown below. Note that the version indicated in parentheses indicates the version of the HAIPE specification that introduced the feature (for features releases after version 1.3.5).

Table 63: HAIPE Model Features

Feature DES Flow Analysis
Table Structures
PT Security Policy Database (version 3.0) Yes Yes
CT Security Policy Database Yes Yes
Security Association Database Yes Yes
Local Enclave Prefix Table (version 3.0) Yes Yes
Peer Enclave Prefix Table Yes Yes
Multicast Address Mapping Table Yes Yes
FFSA Table (version 3.0) Yes No
Registration Transmission Address Table (version 3.0) Yes No
Solicitation Transmission Address Table (version 3.0) Yes No
Solicitation Reception Address Table (version 3.0) Yes No
Protocol Features
IPv6 Addresses Yes No
HAIPE MIB Architecture Compliant Yes Yes
Modeling Vendor-Specific Implementations Yes N/A
Failure/Recovery Modeling Support Yes N/A
Security Policy Fine Grain Selectors (version 3.0) Yes Yes
Anti-Replay Using Sliding Window Yes N/A
Fixed Length Traffic Flow Security Yes Yes
Variable Length Traffic Flow Security (version 3.0) Yes N/A
Version 1.3.5 Transforms Yes Yes
Version 3.0 Transforms Yes Yes
Tunnel Mode Yes Yes
Transport Mode (version 3.0) Yes No
Encryption and Decryption Delay Yes No
Encryption and Decryption Buffers Yes N/A
PT Fragmentation based on SA Path MTU Yes No
PT Fragmentation based on Traffic Flow Security Yes No
CT Fragmentation based on Interface MTU Yes No
ToS Field Bypass (version 1.3.5 only) Yes Yes
DSCP Bypass (version 3.0) Yes Yes
ECN Bypass (version 3.0) Yes N/A
DF Bypass Yes No
IGMP Proxy Mode Yes Yes
IGMP Host Mode (version 3.0) Yes Yes
Dynamic Security Associations Yes No
HAIPE IKE Yes No
HAIPE IKEv2 (version 4.1) Yes No
Orphan SA Recovery Yes N/A
Multiple HIKE SAs to same peer Yes No
Dynamic Peer Discovery Yes No
Generic Discovery Client (version 3.0) Yes No
GDC Discovery of Multiple Prefixes (version 3.1) Yes No
Passive RIP (version 3.0) Yes Yes
RIP Speaker (Version 3.1) Yes No
PDUN Control Message (Version 3.0) Yes N/A
PHRD Control Message (Version 3.0) Yes N/A
Robust Header Compression Yes No
NAT-Traversal (version 3.1) Yes No
Control Plane Signaling (version 3.1) Yes No
Opaque Security Policies (version 3.0) Yes No
Device Classification Yes No

Model Limitations: HAIPE

The following protocol features found in the HAIPE IS are not currently supported. The HAIPE IS version that the item was first introduced is also provided. If no version is indicated, then that particular feature was first introduced in HAIPE IS 1.3.5.:

  • CT Interface ICMP Support
  • IM-PEPD (version 3.1)
  • Legacy Discovery Protocol
  • Mandatory Transmission Rate (version 3.1)
  • Path MTU Discovery (version 3.0)
  • Sequence Numbering and Associated Features
  • Traffic Flow Security Configuration Table (version 3.1)