Model Features: VLAN

The VLAN model suite captures the following protocol behavior:

Table 250: VLAN Model Features

Feature Description Related Attributes
RSM Enables routing and switching in one device. An RSM (route switch module) node can be created using the Device Creator utility to build a switch that includes an IP layer for routing.
Layer-2 Switches (Bridges) Switches are either VLAN-aware or VLAN-unaware.
If VLAN-unaware, switch ignores VLAN tags if they exist in the received packet.
If VLAN aware, switch performs its forwarding task based on the ingress and egress rules defined in the IEEE 802.1Q standard.
VLAN Parameters > Scheme
Set to “Port-Based VLAN”
If VLAN-aware, all supported VLANs must be defined for a switch. (If no VLANs are specified for a node, it supports only VLAN 1 by default.) VLAN Parameters > Supported VLANs
If VLAN-aware, VLAN support must be defined for each port. Supported VLANs for a port must be a subset of supported VLANs for the switch. Switch Port Configuration > VLAN Parameters > Supported VLANs
VLAN Tags Untagged frames carry no VLAN membership info.
VLAN-tagged frames have header tags containing a VLAN ID (VID).
Ports (of VLAN-aware Switches) Can support one or more VLANs. (If no VLANs are specified for a port, it supports only VLAN 1 by default.) Switch Port Configuration > VLAN Parameters > Supported VLANs
Determine VLAN membership for untagged frames by using the Port VLAN Identifier (PVID) of the receiving port. PVID must be configured. Default PVID is 1. Switch Port Configuration > VLAN Parameters > Port VLAN Identifier
Can be Access, Trunk, or Hybrid. Default port type is Access. Switch Port Configuration > VLAN Parameters > Port Type
Access Ports Connect end stations to VLAN-aware network.
Send all frames untagged. If frame is VLAN tagged, they strip off the tag before sending.
Expect to receive VLAN-untagged frames. Insert VLAN tag based on the PVID of the receiving port.
Trunk Ports Connect VLAN-aware nodes
Send all frames VLAN-tagged.
Hybrid Ports Connect both VLAN-aware and unaware nodes.
Send either VLAN-tagged or untagged frames.
Consult Supported VLANs table to determine whether to send VLAN-tagged or untagged.
Send VLAN-tagged frames to VLAN-aware nodes and send VLAN-untagged frames to VLAN-unaware end stations.
Switch Port Configuration > VLAN Parameters > Supported VLANs > Tagging (for hybrid ports)
Specify Send Tagged or Send Untagged.
VLAN Links are defined by the ports they connect.
Trunk links are connections between two trunk ports. They carry frames with VLAN tags.
Access links are entry points to a VLAN-aware portion of the network. They are connected to devices that are unaware of any VLAN membership. Switches remove VLAN tags before transmitting on access links.
Hybrid links transport packets either VLAN-tagged or untagged, based on the VLAN classification of the packet.
Spanning Tree Protocol If set to “Shared”, the traffic of all VLANs use a single spanning tree.
If set to “Multiple”, the node runs Multiple Spanning Tree Protocol (MSTP, IEEE 802.1s) as its spanning tree protocol, which requires the attribute “Bridge Configuration -> Spanning Tree Protocol” set to “RSTP (802.1w).
If set to “Per-VLAN”, the node runs Per-VLAN Spanning Tree Plus (PVST+, a CISCO proprietary protocol) as its spanning tree protocol, which requires the attribute “Bridge Configuration -> Spanning Tree Protocol” set to “STP (802.1D)”.
VLAN Parameters > Spanning Tree Creation Mode
Specify Multiple, Shared, or Per-VLAN.