Mobility Features
Handover
The following handover features are modeled:
- Neighbor advertisements
- Dynamic selection of predefined scanning interval configurations based on measurement levels
- Scanning, which can be initiated by the mobile subscriber or the base station
- Hard handover when initiated by the mobile subscriber. Multiple target base station discovery is also supported.
- ASN anchored mobility for the transfer of service flows and data queues without the need for a Layer-3 handover (mobile IP not needed). When service flows are transferred from the serving base station to the target base station, the transport connections are established during the network entry and the subscriber station does not need to send a DSA request message for each service flow.
Ranging and Initial SS-BS Association
Ranging is supported only when the Efficiency Mode is set to Mobility and Ranging Enabled. The model supports CDMA-based ranging. The initial and periodic phases of ranging are modeled, which helps the SS adjust the connection power with its current BS. Note that only the power adjustment during ranging is modeled. Perfect synchronization is assumed in the WiMAX model; therefore the timing offset estimation and synchronization is not modeled.
When the the Efficiency Mode is set to Mobility and Ranging Enabled, initial SS and BS association is handled through initial ranging. As an SS moves, scanning is used to determine candidate BSs for association, and then initial ranging is performed to complete association.
When any other Efficiency Mode is used, the attribute WiMAX Parameters > SS Parameters > BS MAC Address is used for SS and BS association. When this attribute is set to "Auto-Assigned", the SS is associated with the BS that has the highest received power. Since the mobility is not enabled, this initial association will be used by the SS for the entire duration of the simulation.
Adaptive Modulation and Coding (AMC)
AMC is a feature that enables the SS to use higher data rates when the wireless link condition is sufficiently good. Similarly, it helps the SSs that are close to the cell edge to maintain robust data transmission by making them use conservative (low data rate) modulation and coding schemes.
With AMC, the modulation and coding format is changed based upon the average received signal quality. This allows a service flow to use the best modulation and coding scheme possible without experiencing high BLER.
AMC can be enabled or disabled for each service flow and is enabled by default.
Open Loop Power Control for Uplink Channels
Power Control is a feature that attempts to make an SS use the optimum transmission power in the uplink direction. It adjusts the uplink transmission power of the SS while maintaining a certain link quality. This has two major benefits:
- Reducing transmission power consumption of SSs
- Reducing inter-cell interference (as a result of reduced transmission power)
When this feature is enabled, transmission power of SSs is adjusted to achieve a certain target Signal-to-Noise Ratio (SNR) based on the modulation and coding scheme that the SS is using (adjustment is based on pathloss estimate). This allows the mobile subscriber to use the lowest transmission power that is required for robust data transmission with the current modulation and coding scheme it is using.
This feature can be enabled or disabled on subscriber stations and affects the OFDMA transmissions on uplink channels. The feature is disabled by default.
Interaction of Power Control and AMC
If both power control and AMC are enabled for a given MS, the interaction between both features is set to achieve the maximum possible throughput regardless of the power consumption. Once power control reaches its target SNR for a given modulation and coding scheme, the corresponding AMC threshold will force the MS to move to a modulation coding scheme with higher throughput. This will force power control to increase the power to achieve the next target SNR for the new modulation and coding scheme, which crosses the next AMC threshold, and so on, until maximum power is reached. On the other hand, if AMC has already made MS reach the most aggressive modulation and coding supported by the MS and the wireless link conditions with the BS are still improving, then power control will start reducing the uplink transmission power of the MS accordingly.
Interaction of Power Control and Ranging
If uplink power control is enabled, initial ranging will use the power control power estimation for its initial CDMA code transmission. Subsequent codes are transmitted using the power correction indicated by the base station during the ranging procedure. If power control is not enabled, initial ranging uses half of the maximum MS power for its initial CDMA code transmission.
Access Service Network (ASN) Messages
ASN provides the means to connect mobile subscribers to an IP backbone with session continuity. ASN comprises base stations (BS) and access gateways, called ASN-GW. The interface between the ASN and mobile subscriber is through BS with IEEE 802.16e. The supported ASN messages are shown in the following table.
Table 254: Access Service Network Messages
| Name | Definition |
|---|---|
| HO_Req | Handover request from serving BS to target BS |
| HO_Rsp | Handover response from target BS to serving BS |
| HO_Cnf | Handover confirmation from serving BS to target BS |
| Data_Path_Reg | Sent from serving BS to ASN gateway to update the current position of a mobile node |