Model Scope and Limitations: FDDI
This section discusses the implementation choices made in constructing a model of MAC. Because the model is intended for the purpose of simulation, and particularly for performance estimation, certain parts of the protocol have been simplified or omitted. It is important to understand which mechanisms are modeled in order to gauge whether the model is applicable for a particular simulation study.
The first restriction is that the ring initialization and recovery processes are not modeled explicitly. While the model could be extended to address these areas (it is provided in source code form), its primary usefulness is in obtaining measurements of steady state performance. The initial alignment of station timers and bidding process by which all MAC entities negotiate the TTRT is performed in an essentially static manner, as shall be seen in the detailed description of the models below. This also applies to the distribution of synchronous transmission bandwidth.
A second restriction has to do with the modeling of error conditions and in general, the role of the SMT entity. In its current form, the model makes no attempt to implement the mechanisms related to the detection of damaged frames, or the reporting of errors to SMT. The interface between MAC and SMT is, in fact, not presently incorporated into the implementation of MAC.
The model does incorporate the interfaces between MAC and LLC, as well as those between PHY and MAC. In addition, the primary data transfer features of FDDI are modeled explicitly, including synchronous and asynchronous transmission, definable priority levels for asynchronous frames, and restricted tokens. The effects of station latency and propagation delay are also incorporated into the model. The parameters that may be easily controlled by the user, without having to modify the internals of any of the provided models include:
- the number of stations attached to the ring
- synchronous bandwidth allocation at each station
- requested value of the TTRT by each station (T_Req)
- the address of the station that launches the token as the simulation begins
- the delay incurred by frames and tokens as they traverse a station’s ring interface
- the propagation delay separating stations on the ring
- the mix of asynchronous and synchronous traffic generated at each station
You can configure port-based VLANs on all generic bridge and switch models, and on any vendor-specific models that support this technology. FDDI link models allow you to simulate point-to-point trunk links; a single trunk link can carry traffic for multiple VLANs as specified by IEEE 802.1q.
To configure a VLAN, set the VLAN Scheme attribute to “Port-based VLAN” on the bridge or switch supporting the VLAN. You can assign VLAN identifiers to specific port numbers in the VLAN Port Configuration Table. (To find a link’s port numbers, use Link Interfaces on the Edit Attributes (Advanced) dialog box.) Note that you can assign only one VLAN identifier to a specific port. However, multiple ports can belong to the same VLAN.
The FDDI model incorporates a simulation acceleration feature for modeling the passing of the token from station to station. When the ring experiences an idle period with no transmissions, the token may be passed many times in a very short period, thus generating many simulation events and consuming large amounts of real time while producing data that is of little interest. In order to jump over these periods, a procedure is employed whereby MAC modules register their interest in using the token and also yield the token through a centrally managed set of variables. When an idle period is encountered, token passing is blocked. It is later re-injected into the ring as soon as a station again has a need for it.
Other features of the FDDI model are support for promiscuous and encapsulation modes. In promiscuous mode, the MAC module forwards a copy of all frames received to the higher layer, regardless of the destination address of the frame. In encapsulation mode, the MAC module encapsulates all data packets it receives from the higher layer and decapsulates all frames it receives from the lower layer before forwarding them to the higher layer. Typically, a station would operate in encapsulation mode but not promiscuous mode; however, other combinations are possible. For example, for some applications such as those involving bridging, a station might operate in promiscuous mode but not in encapsulation mode.
The FDDI model supports separate subqueues for synchronous and asynchronous traffic. When separate synchronous queuing is enabled, the MAC module enqueues synchronous frames in a different subqueue from asynchronous frames. When synchronous frames are queued separately, the throughput of synchronous frames at the MAC module improves under heavily loaded conditions.
Implicit in the parameters listed above is a simplification made by the model: the station latency and inter-station propagation delay are assumed to be uniform across the ring. This is primarily done to conveniently support the simulation acceleration option described above.
An additional restriction required to support the simulation acceleration option is that the addresses of stations on a ring must be packed. That is, they must be consecutively numbered from the lowest station address on the ring to the highest. However, the lowest station address may be any non-negative integer.