Windows Installation Troubleshooting
This section provides solutions for problems that may occur during Windows installations or operation. Each problem has a discussion section that explains what is happening and a solution section that explains how to solve the problem. If your problem is not listed here, contact technical support.
Problem
Riverbed Modeler obtains a license from the OPNET License Server through a Windows XP firewall. Both machines are in the same classful network, however Riverbed Modeler fails to obtain a license.
Discussion
The Windows XP firewall blocks Riverbed Modeler licensing traffic.
Solution
Add the op_license_server.exe filename to the exceptions list for the Windows XP firewall. For more information, consult your Windows system administrator.
Problem
Trying to run a licensed program results in the message: The licensing system depends on the following nonexistent service: Tcpip.
Discussion
There is a problem with the TCP/IP software.
Solution
Try installing TCP/IP again (as described in Procedure 2 or Procedure 3), then repeat the step that failed. If the problem persists, contact technical support.
Problem
The Windows setup program reports that TCP/IP is not installed.
Discussion
The licensing system requires that the Windows TCP/IP software be installed. The TCP/IP software, in turn, requires the presence of an installed network adapter driver.
Solution
Use the following procedures to install and configure the necessary software:
- Procedure 2 Installing TCP/IP for a Network Connection (Windows NT 4.0), or Procedure 3 Installing TCP/IP for a Network Connection (Windows 2000)
- Procedure 4 Verifying that a Network Adapter Driver is Installed
- Procedure 6 Configuring TCP/IP
To install TCP/IP for a network connection on a Windows NT 4.0 computer:
Procedure 2: Installing TCP/IP for a Network Connection (Windows NT 4.0)
- Verify that you are logged on as a user with administrator's privileges.
- Insert your Windows CD-ROM into the drive of the install workstation. If a Windows CD-ROM window opens, close it.
- Open the Windows Control Panel and double-click the Network icon. Result: The Network (Network Settings) dialog box opens.
- In the Network (Network Settings) dialog box, click on the Protocols tab. Then click the Add… (Add Software) button. Result: The Select Network Protocol (Add Network Software) dialog box opens.
- Select TCP/IP Protocol (TCP/IP Protocol and related components) from the list of available software and click OK. Result: The TCP/IP Setup dialog box opens.
- If the install workstation is not on a network, answer No to the question about using a DHCP server. If the install workstation is on a network, consult your system administrator for the correct response. Result: The Windows Setup dialog box opens, showing the path to the software on the CD-ROM.
- Verify that the path is
<CD-ROM_drive>:\i386, where<CD-ROM_drive>is the letter of the install workstation CD-ROM drive. Change the path if necessary. - Click Continue. Result: The TCP/IP software is installed from the CD-ROM.
- Click OK, then Close to close the Windows Setup dialog box and return to the TCP/IP Setup dialog box.
- Click on the IP Address tab and enter the IP number, subnet mask, and default gateway. (If you do not know these, ask your system administrator.)
- Click on the DNS tab and enter the host name, domain name and DNS service search order. (The latter value is the IP address of your DNS server.)
- Click OK to reboot your computer.
End of Procedure 2
To install TCP/IP for a network connection on a Windows 2000 computer:
Procedure 3: Installing TCP/IP for a Network Connection (Windows 2000)
-
Verify that you are logged on as an administrator or a member of the administrator's group.
-
Insert your Windows 2000 CD-ROM into the drive of the install workstation. If a Windows CD-ROM window opens, close it.
-
From the Windows Start menu, choose Settings > Network and Dial-up Connections.
-
Double-click on the network connection for which you want install TCP/IP, then click Properties.
-
Click the General tab for a LAN connection, or the Networking tab for all other connection types.
-
If Internet Protocol (TCP/IP) does not appear in the list of installed components, perform the following steps:
- Click Install, then Protocol, then Add. Result: The Select Network Protocol dialog appears.
- Select Internet Protocol (TCP/IP) from the protocols list, then click OK. Result: Internet Protocol (TCP/IP) now appears in the list of supported protocols for the selected connection.
-
Double-click on the Internet Protocol (TCP/IP) list item to open the Internet Protocol (TCP/IP) Properties dialog box.
-
Specify your machine's IP address.
If your network is run on a DHCP server, choose Obtain IP address automatically.
If your network is not run on an DHCP server, click Use the following IP address… and enter the IP address, subnet mask, default gateway, preferred DNS server, and alternate DNS server.
-
Click Advanced… to open the Advanced TCP/IP Settings dialog box, then click the DNS tab.
-
Enter the DNS suffix in the DNS suffix for this connection field.
-
Click OK to close the Advanced TCP/IP Settings dialog box and return to the Internet Protocol (TCP/IP) Properties dialog box.
-
Click OK to close the Internet Protocol (TCP/IP) Properties dialog box.
End of Procedure 3
Confirm that a network adapter driver is installed. If not, install a dummy driver. To verify that a network adapter driver is installed, perform the following procedure.
Procedure 4: Verifying that a Network Adapter Driver is Installed
- If it is not already available, open the Network dialog box.
- Click the Adapters tab to see if there is at least one adapter in the Network Adapters list.
- If there is at least one adapter in the list, continue with Procedure 6.
- If there are no adapters in the list, you must install a "dummy" driver. Continue with Procedure 5.
End of Procedure 4
To install a network adapter driver, do the following procedure.
Procedure 5: Installing a Network Adapter Driver
-
In the Network (Network Settings) dialog box, click the Add… (Add Adapter) button.
-
Select MS Loopback Adapter from the list of available drivers.
-
Click OK (Continue) button. Result: The MS Loopback Adapter Card Setup dialog box opens.
-
Click OK. Result: The standard 802.3 frame type is selected.
-
If prompted, enter the path to the software:
<CD-ROM_drive>:\i386Result: The software is installed from the CD-ROM.
End of Procedure 5
To configure TCP/IP to work with Riverbed Modeler, use the following procedure.
Procedure 6: Configuring TCP/IP
Note: This procedure may result in numerous error messages about various network services. You can ignore these messages.
- In the Network dialog box, click the Protocols tab.
- Click the Properties… (Configure) button. Result: The Microsoft TCP/IP Properties (TCP/IP Configuration) dialog box opens.
- Enter the following configuration information for the workstation. Your network administrator can provide appropriate values for your network.
- IP Address—Enter the network address of the install workstation. If the workstation is not connected to a network, you can enter any value (1.1.1.1, for example).
- Subnet Mask—Enter a value appropriate for the install workstation, if one is not entered automatically. (With the example IP Address in step 3a, the Subnet Mask would be 255.0.0.0.)
- Default Gateway—Enter the address of the gateway used by the install workstation. Again, if the workstation is not connected to a network, you can enter any value (1.1.1.1, for example).
- Click OK.
- If an alert dialog about adapter cards with an empty primary WINS address appears, you can generally continue by clicking Yes. If a problem occurs, consult your network administrator.
- Close the Network (Network Settings) dialog box. Restart the install workstation if a dialog box suggesting this appears.
End of Procedure 6
The necessary TCP/IP software is now ready for use with the Floating License System.